The Best Shark Hooks And Leaders

This Listing is for our 16/0 carbon steel inline circle hook shark rig (270# test, 7×7 49 strand construction bright stainless steel cable). Our circle hook shark rigs start with an eleven foot piece of 49 strand stainless steel cable and are double crimped with brass sleeves to a commercial carbon steel circle hook and 4/0 Rosco Brass Swivel. The finished rig is just over ten feet long which keeps most sharks far enough away from your mainline but is manageable enough at the side of the boat. Like all of our rigs, each one is made by hand in the USA. A key feature to all Cardinal Tackle Shark Rigs is the protected connections. After double-crimping the hook and swivel, we cover it with a short length of heat shrink tubing. The heat shrink tubing: (1) in the event of a tangle or crossed liens, it prevents frayed ends of shark wire cutting up your monofilament | (2) helps protect your hands when leadering or even just changing baits | (3) less damage to soft baits if you bury the hook | (4) cuts down on nasty pieces of old bait fish stuck to your rig if you have to put it away for another trip. This non-stainless, non-offset, circle hook shark rig is New York E. C. L. § 13-0338 compliant.

5′ bite leader with carbon steel circle hook can be used for shark, grouper, halibut, or any other big game species that needs protection from bite offs. All of our tackle is hand made in the USA and built on calibrated bench crimpers.

This Listing is for our 18/0 carbon steel inline circle hook shark rig (480# test, 7×7 49 strand construction bright stainless steel cable). Our circle hook shark rigs start with an eleven foot piece of 49 strand stainless steel cable and are double crimped with brass sleeves to a commercial carbon steel circle hook and 4/0 Rosco Brass Swivel. The finished rig is just over ten feet long which keeps most sharks far enough away from your mainline but is manageable enough at the side of the boat. Like all of our rigs, each one is made by hand in the USA. A key feature to all Cardinal Tackle Shark Rigs is the protected connections. After double-crimping the hook and swivel, we cover it with a short length of heat shrink tubing. The heat shrink tubing: (1) in the event of a tangle or crossed liens, it prevents frayed ends of shark wire cutting up your monofilament | (2) helps protect your hands when leadering or even just changing baits | (3) less damage to soft baits if you bury the hook | (4) cuts down on nasty pieces of old bait fish stuck to your rig if you have to put it away for another trip. This non-stainless, non-offset, circle hook shark rig is New York E. C. L. § 13-0338 compliant.

Specification:

Type: Shark Rig

Test: 400lb

Quantity: 1pack/2packs

Material: Stainless Steel+Nylon

Features:

1. Well made ready rig and good value. Tooth guard. Very heavy duty. Large hook

2. 400lb nylon coated stainless steel cable, strong and sturdy

3. Hand-tied and machine crimped for strength, shrink-wrapped for abrasion resistance

4. If you are looking for some rigs for the big boys, you have to buy this/try this.

Note:

The Hooks Are Really Sharp, so Care Should Be Taken When Handling Them.

DO NOT Put it on the Place Where Children Can Take it Easily.

The function of fishing wire leader
1. Avoid the momentary pulling of the throwing, the friction between the main line and the guide ring will damage to the main line
2. After dragging the bait or caught fish, protect the front end of the main line to avoid rubbing against obstacles;
3. Conceal the main line, reduce the fish alertness after finding the fishing line
4, offset the momentary pulling force that may occur after caught fish, buffering function
5. The marking function when recovering the bait to prevent the bait from colliding with the leader ring of the fishing rod and injuring people;
6.The use of reliable front wires higher than the strength of the main line increases the possibility of trying to choose a finer main line, thus making the throw easier and the bait flying farther

This Listing is for our 20/0 carbon steel inline circle hook shark rig (480# test, 7×7 49-strand construction bright stainless steel cable). Our shark rigs start with an eleven foot piece of 49 strand stainless steel cable and are double crimped with brass sleeves to a commercial carbon steel circle hook and 4/0 Rosco Brass Swivel. The finished rig is ten feet long which keeps most sharks far enough away from your mainline but is manageable enough at the side of the boat. Like all of our rigs, each one is made by hand in the USA. A key feature to all Cardinal Tackle Shark Rigs is the protected connections. After double-crimping the hook and swivel on our benchtop press, we cover it with a short length of heat shrink tubing. The heat shrink tubing: (1) in the event of a tangle or crossed liens, it prevents frayed ends of shark wire cutting up your monofilament | (2) helps protect your hands when leadering or even just changing baits | (3) less damage to soft baits if you bury the hook | (4) cuts down on nasty pieces of old bait fish stuck to your rig if you have to put it away for another trip. Folks also use these rigs for land based shark fishing with a heavy monofilament leader. This non-stainless, non-offset, circle hook shark rig is New York E. C. L. § 13-0338 compliant.

Octopus fishing hook

Size and quantity details:
Size————Length—————–Width
6/0————1.77inch—————-1.1inch
5/0————1.54inch—————-0.94inch
4/0————1.42inch—————-0.91inch
3/0————1.18inch—————-0.87inch
2/0————1.10inch—————-0.78inch
1/0————1.06inch—————-0.71inch
1#————-0.94inch—————-0.63inch
2#————-0.75inch—————-0.59inch
4#————-0.71inch—————-0.51inch

1. Please allow 1-2mm difference due to manual measurement.
2. Real color may slightly different from pictures due to computer screen’s resolution, brightness, contrast etc. Hope understanding.

Warranty: 
★Persei adhere to Amazon Return Policy. 
★Persei will take full responsibility for any quality problems within 30 days.
  ■Any question please contact us directly.